Updated Nov 19, 2026· 11 min read

Key takeaways

  • Compare the best dummy batteries for Canon, Sony, Nikon and Fujifilm cameras, from AC adapter kits to USB-C PD and D-Tap couplers for long shoots.

The best dummy battery is the one built for the exact battery family your camera already uses, because a DC coupler has to match the shape, contacts and voltage of the cell it replaces. For most Canon shooters that means an LP-E6 kit such as the Kimaru ACK-E6, for Sony owners it means an NP-FZ100 kit like the Neewer coupler set or an NP-FW50 kit like the F1TP AC-PW20, Nikon Z and DSLR bodies take an EP-5B coupler such as the USB-C powered Raeisusp, and Fujifilm X and GFX bodies take an NP-W235 coupler such as the D-Tap powered Topcine. Each pick below is a complete published-spec match for its battery family, with the kit contents, input and output figures, and camera lists taken from the maker listings.

As an Amazon Associate, we earn from qualifying purchases.

Table of Contents

How a Dummy Battery Works

A dummy battery is a battery-shaped DC coupler with no cells inside. It slides into the camera battery compartment, its contacts meet the same terminals a real pack uses, and a thin cable exits through the small rubber port in the battery door so the door can close over it. The other end of the cable connects to an AC adapter, a USB-C Power Delivery source, or a cinema battery, and that external source feeds the camera a steady DC voltage in place of the pack. The camera simply sees constant power, so recording, streaming, time-lapse sequences and long studio sessions run without a battery swap and without the heat a working cell adds inside the body.

Because the coupler is molded to one battery family, fit is everything. An LP-E6 coupler cannot serve an NP-FZ100 body, and an NP-FW50 coupler will not fit a camera built for the larger NP-FZ100. Many couplers also carry a decoding chip that reports charge data to the camera, which keeps warning messages away on bodies that check for a genuine pack. The five kits below cover the most common mirrorless and DSLR battery families, and each one lists its confirmed camera models so you can match your body before ordering.

How to Choose the Right Dummy Battery

Match the battery model first. Pull your current pack out and read the model printed on it: LP-E6, NP-FZ100, NP-FW50, EN-EL15 and NP-W235 are the families covered here. Camera names alone can mislead, since one brand sells bodies in several families. The original Sony ZV-E10 uses NP-FW50 power, for example, while the ZV-E10 II uses NP-FZ100 power.

Pick the power source that suits the room. AC adapter kits plug into a wall outlet and are the simplest route for a fixed desk, studio or streaming corner. USB-C PD couplers run from a PD wall charger or a PD power bank, which suits travel and tidy cable runs. D-Tap couplers draw from V-Mount or Gold Mount cinema batteries and belong on rigs that already carry those packs.

Check the output figures. The adapter output should sit at the voltage your battery family expects, and the listing for each kit below prints its input range, output voltage and current. A worldwide 100 to 240 volt input also matters if you plan to shoot outside your home country.

Confirm the door closes. Nearly every camera needs the battery door shut over the coupler cable for the body to power on, and makers state this in their kit notes. Route the cable through the port in the door rather than pinching it under the latch.

1. Kimaru ACK-E6 AC Power Adapter Kit for Canon LP-E6

Tier: Budget

The Kimaru ACK-E6 kit is the straightforward wall-powered route for the huge installed base of Canon bodies that run on LP-E6 family packs. The box pairs the ACK-E6 AC adapter with the DR-E6 style dummy battery, and the decoded coupler covers the LP-E6, LP-E6N and LP-E6NH variants, so one kit serves everything from a 5D Mark IV to an EOS R6. The listing rates the adapter output at DC 8.0 volts and 3 amps for 24 watts, with short circuit protection among the published features, and the input accepts 100 to 240 volts for travel use. Kimaru states plainly that the kit does not fit the EOS R5 Mark II or the R6 Mark III, which use a newer pack, so owners of those two bodies should look at a coupler built for their own battery family instead.

Specs

  • Battery family: Canon LP-E6, LP-E6N, LP-E6NH (DR-E6 DC coupler)
  • Kit contents: ACK-E6 AC power adapter, LP-E6 dummy battery / DC coupler
  • Input: 100 to 240 V, 0.6 A, 50/60 Hz
  • Output: DC 8.0 V / 3 A, 24 W
  • Model number: TDX-080300
  • Item weight: 260 g
  • Published features: short circuit protection, charging indicator
  • Compatible cameras: Canon EOS R, R5, R6, R6 Mark II, R7, 90D, 80D, 70D, 60D, 60Da, 6D, 6D Mark II, 7D, 7D Mark II, 5D Mark II, 5D Mark III, 5D Mark IV, 5Ds, 5Ds R
  • Not compatible: Canon EOS R5 Mark II, EOS R6 Mark III

2. F1TP AC-PW20 Dummy Battery Kit for Sony NP-FW50

Check price on Amazon

Tier: Budget

Sony kept the compact NP-FW50 pack across a long run of APS-C and early full-frame bodies, and the F1TP AC-PW20 kit is the matching wall-powered coupler for that family. The kit bundles the AC-PW20 adapter, the NP-FW50 dummy battery and a US power cord, and the listing gives a combined cord reach of 12 feet, which leaves freedom to place the camera on a desk or tripod without the adapter dangling from the outlet. Output is rated at DC 7.6 volts and 2 amps for 15.2 watts, and the input accepts 100 to 240 volts. The compatibility list runs from the ZV-E10 vlogging body through the a6000 series and the RX10 II, III and IV bridge cameras. Note the boundary the maker draws: this kit does not serve NP-FZ100 bodies such as the a7 III, and it does not fit the ZV-E10 II, the RX100 line or the ZV-1.

Specs

  • Battery family: Sony NP-FW50 (AC-PW20 coupler)
  • Kit contents: AC-PW20 AC power adapter, NP-FW50 dummy battery, US power cord
  • Input: 100 to 240 V
  • Output: DC 7.6 V / 2 A, 15.2 W
  • Cord reach: 12 ft as listed
  • Item model number: AC-PW20 NP-FW50
  • Manufacturer: FIT-POWER
  • Compatible cameras: Sony ZV-E10, a6000, a6100, a6300, a6400, a6500, a5000, a5100, a7, a7 II, a7R, a7S, a7R II, a7S II, RX10 II, RX10 III, RX10 IV, NEX-5, NEX-6, NEX-7
  • Not compatible: Sony ZV-E10 II, a7 III and other NP-FZ100 bodies, RX100 series, ZV-1

3. Neewer NP-FZ100 AC Power Supply Adapter and DC Coupler Kit

Check price on Amazon

Tier: Mid-range

Current Sony full-frame and cinema bodies run on the larger NP-FZ100 pack, and this Neewer kit is the AC-powered coupler set built for that family. The box holds the NP-FZ100 dummy battery, an AC/DC adapter and a power cord, so the whole chain from wall outlet to camera arrives in one package. The published compatibility list is broad, spanning the a7 III and a7 IV, the a7R III through a7R V, the a7S III, the a1, the a9 II, the a6600 and a7C, plus the FX3 and FX30 cinema bodies and the ZV-E1. Neewer adds one honest firmware note in its listing: on the FX3, FX30, A7C II, A7CR and ZV-E1 with the latest firmware, the coupler still powers the camera, yet the on-screen battery level may not display. For streamers and video shooters who leave a body mounted for hours, that trade is minor next to never pausing for a pack swap.

Specs

  • Battery family: Sony NP-FZ100
  • Kit contents: NP-FZ100 dummy battery, AC/DC adapter, power cord
  • Model number: 10099074
  • Compatible cameras: Sony a1, a9 II, a7R III, a7R IV, a7R V, a7S III, a7 III, a7 IV, a6600, a7C, ZV-E1, FX3, FX30
  • Published note: on FX3, FX30, A7C II, A7CR and ZV-E1 with the latest firmware, the camera is powered but the battery level may not be shown on screen

4. Raeisusp EP-5B USB-C PD Dummy Battery Kit for Nikon EN-EL15

Check price on Amazon

Tier: Mid-range

Nikon Z bodies and the long line of EN-EL15 DSLRs take the EP-5B power connector, and the Raeisusp kit feeds that coupler from USB-C Power Delivery instead of a dedicated wall brick. The box holds a USB-C cable, the EP-5B DC coupler and a PD adapter, so the camera can run from a PD wall charger at a desk or from a PD power bank in a bag, which suits time-lapse work away from an outlet. The published camera list covers the Z5, Z6 and Z7 mirrorless bodies, the D500, D600, D750, D800, D810 and D850 DSLRs, the D7000, D7100, D7200 and D7500 crop bodies, and even the older Nikon 1 V1. Because the power source is yours to choose, check that your PD charger or bank is rated for camera duty and keep the coupler lead routed through the battery door port so the door latches fully.

Specs

  • Battery family: Nikon EN-EL15, EN-EL15a (EP-5B power connector)
  • Kit contents: USB-C cable, EP-5B DC coupler, PD adapter
  • Power source: USB-C Power Delivery charger or power bank
  • Compatible cameras: Nikon Z5, Z6, Z7, D500, D600, D750, D800, D810, D850, D7000, D7100, D7200, D7500, 1 V1
  • Date first available: March 18, 2021

5. Topcine D-Tap to NP-W235 Dummy Battery for Fujifilm

Check price on Amazon

Tier: Premium

Fujifilm X-T4, X-T5 and GFX shooters who already power a rig from V-Mount or Gold Mount packs can feed the camera from the same brick with the Topcine D-Tap coupler. The dummy battery is fully decoded, and its built-in step-down module accepts 14.4 to 16.8 volts from the D-Tap port and delivers 7.2 to 8.4 volts at up to 3 amps to the NP-W235 compartment. The coiled cable runs from 20 inches at rest to 48 inches extended, which keeps slack tidy on a cage or gimbal while still reaching a battery plate mounted behind the camera. The published fit list covers the X-S20, X-T4, X-T5 and X-H2S, plus the GFX 50S II and GFX 100S medium format bodies. There is no wall adapter in this kit by design: it is a rig power cable, so it belongs in the roundup as the premium route for Fujifilm owners who shoot video from a shared cinema battery.

Specs

  • Battery family: Fujifilm NP-W235
  • Input: 14.4 to 16.8 V via D-Tap (V-Mount or Gold Mount battery)
  • Output: 7.2 to 8.4 V, 3 A maximum
  • Cable: coiled, 20 in at rest to 48 in extended
  • Chip: fully decoded, built-in step-down module
  • Item model number: NPW235
  • Compatible cameras: Fujifilm X-S20, X-T4, X-T5, X-H2S, GFX 50S II, GFX 100S
  • Date first available: January 14, 2023

Setup Tips for Reliable Continuous Power

Seat the coupler exactly as you would a real pack, then guide its cable through the rubber port in the battery door and close the door until it latches. Most bodies refuse to power on with the door open, and makers repeat that instruction in their kit notes. Give the adapter brick air space rather than burying it under cloth or paper, and keep cable runs clear of tripod legs so a bump cannot tug the coupler loose mid-recording. If your camera shows a battery warning with a third-party coupler, a decoded model such as the Topcine above, or a firmware note such as the one Neewer publishes for its NP-FZ100 kit, usually explains the behavior. Finally, keep one charged genuine pack in the bag: a coupler only helps where its power source reaches, and a real battery still covers handheld work.

Frequently Asked Questions

What is a dummy battery and how does it power a camera?

A dummy battery is a battery-shaped DC coupler with no cells inside. It sits in the battery compartment, connects through a cable to an AC adapter, a USB-C Power Delivery source or a cinema battery, and feeds the camera steady external power so long sessions run without a battery swap.

How do I choose the right dummy battery for my camera?

Match the model printed on your existing battery pack, such as LP-E6, NP-FZ100, NP-FW50, EN-EL15 or NP-W235, then confirm your exact camera body appears in the kit compatibility list. After that, choose the power source that suits your setup: wall AC for a fixed desk, USB-C PD for power bank flexibility, or D-Tap for a cinema rig.

Can a dummy battery damage my camera?

A coupler built for your battery family delivers the voltage that family expects, and the kits here publish their input and output figures along with protection features such as short circuit protection on the Kimaru adapter. Risk grows with mismatched gear, so never force a coupler from another battery family into the compartment, and use the adapter or PD source the listing calls for.

Does the battery door need to close over the coupler cable?

Yes, on nearly every camera the body will only power on with the battery door fully closed. Coupler cables are made thin for this reason and exit through the small rubber port in the door, so route the cable through that port rather than trapping it under the latch.

Conclusion

A dummy battery turns a mirrorless or DSLR body into a camera that runs as long as the outlet, power bank or rig battery holds out, and the right choice is always the coupler molded for your pack. Canon LP-E6 owners get a simple wall-powered answer in the Kimaru ACK-E6, Sony NP-FW50 owners get the long-cord F1TP AC-PW20 kit, and current Sony NP-FZ100 bodies are served by the Neewer AC kit. Nikon EN-EL15 shooters gain power bank freedom with the USB-C PD Raeisusp EP-5B, while Fujifilm NP-W235 owners on cinema rigs can draw from the same V-Mount brick as the rest of the rig with the Topcine D-Tap coupler. Match the battery model, confirm the body list, close the door over the cable, and battery swaps leave your long shoots for good.

A
admin
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Dummy Batteries: 5 Couplers for Nonstop Camera…Check price on Amazon