Updated Nov 19, 2026· 11 min read

Key takeaways

  • Compare the best battery grips for Canon, Sony, Nikon and Fujifilm mirrorless cameras, with specs on battery capacity, controls and weather sealing.

A battery grip bolts to the base of a mirrorless camera, adds room for a second battery, and puts a full set of controls under your hand when the camera turns sideways for portrait work. The short answer: Canon shooters on current EOS R bodies should look first at the BG-R20, Sony Alpha owners at the VG-C4EM, Fujifilm X-H2 and X-H2S owners at the VG-XH, and Nikon Z8 owners who want a lower tier option at the Neewer MB-N12. A fifth pick, the Neewer replacement for the Canon BG-R10, covers EOS R5 and R6 bodies on a budget tier. Every pick below is matched to specific camera models, so check your exact body name against the compatibility line in each Specs block before ordering.

As an Amazon Associate, we earn from qualifying purchases.

Table of Contents

How to Choose a Battery Grip

Match the exact camera body

Compatibility is the first filter and the one most often missed. A battery grip is shaped for one body or one small family of bodies, and its electrical contacts have to line up with the contact points inside that camera’s battery compartment. A grip built for the Canon EOS R5 Mark II also fits several other EOS R bodies, as the BG-R20 section below shows, while the Neewer MB-N12 fits the Nikon Z8 alone. Brand alone is not enough: a Sony grip for the a7R IV generation does not fit the earlier a7 III generation, which used a different battery and a different grip. Write down your full model name, including any Mark suffix, and match it word for word against the maker’s compatibility list.

Battery type and battery count

Most current grips hold two batteries, and most also run on a single battery if only one is loaded. The battery type matters as much as the count. Canon’s LP-E6 line spans the LP-E6, LP-E6N, LP-E6NH and the newer LP-E6P, and the newest EOS R bodies restrict which of those packs unlock full performance. Sony’s current Alpha grips take the NP-FZ100, Nikon’s Z grips take the EN-EL15 family, and Fujifilm’s X-H grips take the NP-W235. If you already own spare batteries, a grip that uses the same packs saves a second purchase. The Neewer MB-N12, for example, charges EN-EL15c batteries over USB-C but cannot charge the older EN-EL15a or EN-EL15 inside the grip.

Vertical controls

The second job of a grip is control placement. A good grip repeats the camera’s shutter button, command dials and focus controls on its vertical face, so portrait orientation work uses the same hand positions as landscape work. Look for a shutter button with a lock switch, front and rear command dials, an AF-ON button and a multi-selector or focus lever. The Fujifilm VG-XH goes further and repeats the Q button and AE-L button as well, plus a toggle for the camera’s Eco, Normal and Boost performance modes. Photographers who shoot long portrait sessions, weddings or vertical video benefit most from a complete control set, because every trip back to the body controls breaks the rhythm of the shoot.

Charging, hot swapping and sealing

Three further published details separate the picks. First, charging: several grips let batteries charge while mounted, either through the camera’s USB port or through a USB-C port on the grip itself, which turns the grip into a travel charger. Second, hot swapping: the Neewer MB-N12 keeps the camera powered from one battery while the other is exchanged, a feature aimed at event and sports work where the camera cannot go dark. Third, sealing and build: the Canon, Sony and Fujifilm grips in this guide carry dust and moisture resistance matched to their camera bodies, and the Fujifilm VG-XH is rated for operation down to minus 10 degrees Celsius. The Neewer grips use simpler construction, and Neewer’s own manual for the MB-N12 advises keeping the grip dry, so plan accordingly if you shoot in rain.

Canon BG-R20 Battery Grip

Check price on Amazon

The BG-R20 is Canon’s current grip for the EOS R5 and EOS R6 families, and it is the natural first choice for anyone running an EOS R5 Mark II. It holds one or two LP-E6 series batteries and supports the LP-E6P pack at its full rated discharge current of 6.0A, which Canon ties to the higher performance modes of the R5 Mark II. Owners of the older EOS R5, EOS R6, EOS R6 Mark II and EOS R6 Mark III can use it as well, and on those bodies the LP-E6 remains usable, while Canon notes the LP-E6 cannot be used with the R5 Mark II. The vertical face carries buttons and dials for portrait shooting, with a multi-controller position that Canon revised relative to the earlier BG-R10. Construction follows the same dust and drip resistance approach as the camera bodies, and the LP-E6P can charge inside the grip through the camera using Canon’s USB Power Adapter PD-E2. A DC coupler connection, the DR-E6P, is also supported for studio work on mains power. For Canon shooters this is the premium tier pick, with the widest battery support list of any Canon grip.

Specs
– Compatibility: Canon EOS R5 Mark II, EOS R5, EOS R6 Mark III, EOS R6 Mark II, EOS R6
– Batteries: One or two LP-E6P, LP-E6NH, LP-E6N or LP-E6 packs (LP-E6 excluded on EOS R5 Mark II)
– Model number: 6762C001
– Dimensions: Approximately 143.2 x 109.4 x 80.3 mm
– Weight: Approximately 354 g including battery magazine, excluding batteries
– Features: Vertical shooting controls, revised multi-controller position, USB charging support for LP-E6P via PD-E2 adapter, DR-E6P DC coupler support, dust and drip resistance

Sony VG-C4EM Vertical Grip

Check price on Amazon

Sony’s VG-C4EM is the maker’s grip for the Alpha full-frame line built around the NP-FZ100 battery. It launched with the a7R IV and a9 II, and Sony also lists it for the a7 IV, a7S III, a7R V and a1, which makes it the single grip covering most current Alpha bodies. The shell is magnesium alloy, matching the construction of the cameras, and the sealing follows the same dust and moisture resistant approach as the bodies it mounts to. Two NP-FZ100 batteries load on a tray, and the camera draws them down in sequence, so a depleted pack can be exchanged while the second keeps the camera running. The batteries can also be charged through the camera’s USB port with the grip attached. The vertical face repeats the controls Alpha shooters reach for most: a shutter button, AF-ON and AEL buttons, front and rear control dials and a multi selector, placed to mirror the body’s layout. For Sony owners this is the premium tier choice for event, portrait and wildlife work.

Specs
– Compatibility: Sony a7R IV, a9 II, a7 IV, a7S III, a7R V, a1
– Batteries: One or two NP-FZ100 packs, loaded on a tray
– Model number: VGC4EM
– Construction: Magnesium alloy shell with dust and moisture resistance
– Controls: Shutter button, AF-ON button, AEL button, front and rear control dials, multi selector
– Features: Sequential battery drain with mid-session pack exchange, charging of grip batteries through the camera USB port

Fujifilm VG-XH Vertical Battery Grip

Check price on Amazon

The VG-XH is Fujifilm’s grip for the X-H2 and X-H2S, the two flagship X Series bodies with a full control layout. It holds two NP-W235 batteries in addition to the pack inside the camera, for three batteries in total, and Fujifilm’s listing data puts the combined capacity at up to approximately 1,700 frames between charges. The control set is the most complete in this guide: a secondary shutter release, a focus lever, AE-L and AF-ON buttons, an Fn button, a Q button and front and rear command dials all sit on the vertical face. A toggle switch selects the camera’s Eco, Normal or Boost performance modes from the grip, which matters on these bodies because Boost mode governs frame rate and viewfinder refresh behaviour. The grip is dust and moisture resistant and is rated for operation at temperatures down to minus 10 degrees Celsius, matching the cold weather rating of the cameras. For X-H2 and X-H2S owners, the VG-XH is the mid-range tier pick that extends power and handling.

Specs
– Compatibility: Fujifilm X-H2, X-H2S
– Batteries: Two NP-W235 packs in the grip, plus one in the camera body
– Model number: 16757320
– Controls: Shutter button, focus lever, AE-L button, AF-ON button, Fn button, Q button, front and rear command dials
– Features: Eco, Normal and Boost performance mode toggle, dust and moisture resistance, operation down to minus 10 degrees Celsius
– Published capacity figure: Up to approximately 1,700 frames with a full battery set

Neewer MB-N12 Vertical Battery Grip for Nikon Z8

Check price on Amazon

Nikon Z8 owners who want a grip below the maker’s premium tier have this Neewer replacement for the MB-N12 pattern. It accepts one or two EN-EL15c batteries and stays backward compatible with the EN-EL15b, EN-EL15a and EN-EL15, so existing Nikon spares carry over. Its headline feature is hot swapping: with two batteries loaded, one can be removed and replaced while the camera keeps drawing power from the other, which suits wedding and sports coverage where a power gap is not acceptable. EN-EL15c packs also charge inside the grip over a USB Type-C cable, although Neewer’s manual notes the older EN-EL15a and EN-EL15 cannot charge this way. The vertical face carries a shutter release, main and sub command dials, an AF-ON button, an Fn button and a multi selector, and the base has a standard tripod socket. The trade-offs sit in the build: the shell is plastic, and the manual advises keeping the grip dry, so it lacks the weather sealing story of the maker grips above.

Specs
– Compatibility: Nikon Z8
– Batteries: One or two EN-EL15c, EN-EL15b, EN-EL15a or EN-EL15 packs
– Dimensions: 5.5 x 4.64 x 3 inches (139 x 118 x 77 mm)
– Weight: 9.2 oz / 261 g without batteries
– Controls: Shutter button, main and sub command dials, AF-ON button, Fn button, multi selector, control lock
– Features: Hot swappable battery bay, USB Type-C charging for EN-EL15c packs inside the grip, tripod socket on the base, plastic construction

Neewer Battery Grip Replacement for BG-R10

Check price on Amazon

Canon’s BG-R10 pattern also has a Neewer replacement, aimed at EOS R5, EOS R5C, EOS R6 and EOS R6 Mark II owners working within the budget tier. It runs on one or two LP-E6, LP-E6N or LP-E6NH batteries, the same packs the cameras use, so an existing spare becomes the second pack in the grip. A shutter release and a control dial sit on the vertical face for portrait orientation work, with a lock switch to prevent accidental presses when the camera hangs at your side. The listing gives the model number as 10101812 and publishes dimensions of 20.3 x 15.6 x 9.1 cm with a weight of 304.47 grams. What this tier gives up, relative to Canon’s own grips, is the newest battery support: there is no LP-E6P high-current support here, so EOS R5 Mark II owners should choose the BG-R20 above instead. For the large installed base of EOS R5 and R6 bodies, though, this is a straightforward way to double battery capacity and gain vertical controls while staying in the budget tier.

Specs
– Compatibility: Canon EOS R5, EOS R5C, EOS R6, EOS R6 Mark II
– Batteries: One or two LP-E6, LP-E6N or LP-E6NH packs
– Model number: 10101812
– Dimensions: 20.3 x 15.6 x 9.1 cm (published listing figures)
– Weight: 304.47 g (published listing figure)
– Controls: Vertical shutter release, control dial, lock switch

Frequently Asked Questions

Are battery grips interchangeable between camera models?

No. A battery grip is built for named camera models only, and its shape, contacts and firmware handshake all assume those bodies. Some grips cover a small family, such as the Canon BG-R20 across the EOS R5 and EOS R6 lines, while others fit a single body, such as the Neewer MB-N12 for the Nikon Z8. Always match the full model name on your camera, including Mark numbers, against the compatibility line published for the grip.

How much longer can you shoot with a battery grip?

A two-battery grip roughly doubles the frames or recording time of the single in-body battery, and makers publish combined figures for their systems. Fujifilm’s listing data for the VG-XH cites up to approximately 1,700 frames with two batteries in the grip plus one in the X-H2 body. Actual endurance varies with temperature, screen use and shooting mode, and the Boost mode on Fujifilm bodies draws power faster than Eco mode.

Can batteries charge while they are inside the grip?

On several current models, yes. The Neewer MB-N12 charges EN-EL15c batteries inside the grip over USB-C, the Canon BG-R20 supports charging an LP-E6P through the camera with Canon’s PD-E2 USB power adapter, and the Sony VG-C4EM lets its two NP-FZ100 packs charge through the camera’s USB port. Charging support often depends on the battery revision, so check the pack named in the grip’s manual before relying on it while travelling.

Do battery grips change image quality?

A grip does not change the sensor or the image files a camera produces. What it can change is camera behaviour around power: the Canon BG-R20 supports the LP-E6P battery at its full 6.0A discharge rating, which the EOS R5 Mark II needs for its full performance envelope, and the Fujifilm VG-XH adds a toggle for the Eco, Normal and Boost performance modes. Treat a grip as a power and handling accessory whose benefits are endurance, balance with long lenses and complete vertical controls.

Conclusion

The right battery grip is the one built for your exact camera body, loaded with the newest battery revision that body supports. Canon EOS R5 Mark II owners get the fullest feature set from the BG-R20, Sony Alpha owners from the magnesium alloy VG-C4EM, and Fujifilm X-H2 and X-H2S owners from the VG-XH with its performance mode toggle. Nikon Z8 owners who value hot swapping and in-grip charging over weather sealing can step down a tier to the Neewer MB-N12, and EOS R5 and R6 owners on the budget tier are served by the Neewer BG-R10 replacement. Confirm the model name, battery type and control list in the Specs blocks above, then order with confidence.

A
admin
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Battery Grips for Canon, Sony, Nikon and…Check price on Amazon